- If your device is dead, you can unbrick using the Stock ROM file
- You can fix or repair the IMEI on your device using DB files from Stock ROM
- Remove any malware or Adwares from Motorola G7 Play
- You can fix the boot loop issue on Motorola G7 Play
- Fix Unfortunately, the app has stopped error on Motorola G7 Play
- Fix Network related issue
- Patch Boot image to Root using Magisk: Mediatek Guide or Spreadtrum Guide
- You can unroot Motorola G7 Play
- To Reset or Remove FRP on your device: Mediatek FRP Guide or Spreadtrum FRP Guide
- Restore Motorola G7 Play back to Factory State
Moto G7 Play XT1952-1 Firmware Flash Files:
lash File Name: QPYS30.52-22-8-9
Model: XT1952-1
Android Version: 10
|
Download |
Flash File Name: PPYS29.105-134-9
Model: XT1952-1
Android Version: 9.0 |
Download |
Steps to Install Motorola XT1952-1 Firmware Flash File
If you have downloaded the firmware, then follow this guide to flash the stock firmware manually on your Moto G7 Play XT1952-1. Make sure to follow the steps carefully.
Pre-Requirements:
Disclaimer:
GetDroidTips will not be held responsible for any kind of hardware or software damage to your device by following this guide. Proceed at your own risk
Firmware Installation Guide:
Check out the firmware flashing guide below for the Moto G7 Play XT1952-1. First, make sure to install or extract the adb and fastboot tool on your PC. Now enter the bootloader on your device.

Step 1. Bootloader Mode
Enter bootloader mode on your phone. To boot first, turn your phone off. Once your device turned off completely, press and hold volume down, and turn it on. You should see the bootloader screen.
Step 2. Connect Your Device to PC:
After booting your Moto G7 Play into bootloader mode, now connect it to the PC using the USB Cable.
Step 3. Download Stock ROM/Firmware:
To get the full ROM, you can use the LMSA or Rescue and Smart Assistant Tool. Download the zip file and copy it to somewhere on your PC. LMSA tool will unzip the file and will remove the zip file you downloaded.

You can also download the full stock ROM from the above download flash file section on this guide.
Step 4. Flashing Guide:
- The next step is to open the command window and go to the adb folder

- Enter the following command to flash the firmware.
fastboot flash partition gpt.bin
fastboot flash bootloader bootloader.img
fastboot flash modem NON-HLOS.bin
fastboot flash fsg fsg.mbn
fastboot erase modemst1
fastboot erase modemst2
fastboot flash bluetooth BTFM.bin
fastboot flash dsp adspso.bin
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash system system.img_sparsechunk.0
fastboot flash system system.img_sparsechunk.1
fastboot flash system system.img_sparsechunk.2
fastboot flash system system.img_sparsechunk.3
fastboot flash system system.img_sparsechunk.4
fastboot flash system system.img_sparsechunk.5
fastboot flash system system.img_sparsechunk.6
fastboot flash system system.img_sparsechunk.7
fastboot flash system system.img_sparsechunk.8
fastboot flash system_b system_b.img_sparsechunk.0
fastboot flash system_b system_b.img_sparsechunk.1
fastboot flash system_b system_b.img_sparsechunk.2
fastboot flash vendor vendor.img_sparsechunk.0
fastboot flash vendor vendor.img_sparsechunk.1
fastboot flash oem oem.img
fastboot flash oem_b oem_other.img
fastboot erase carrier
fastboot erase userdata
fastboot erase ddr
fastboot oem fb_mode_clear
fastboot reboot
- Now your device will reboot into bootloader with the firmware you installed
That’s it, guys. We hope this guide was helpful to you. Feel free to ask in the comment below for additional queries.