How to Enter EDL Mode on Redmi Note 9 Pro (joyeuse)
Follow this instruction carefully to boot your device into EDL Mode (aka Emergency DownLoad Mode)
Method 1: Using ADB
- Download ADB and Fastboot Tool and extract it in your PC (C:/ Drive)
- Connect your device to your PC
- Open the adb command and enter the command
.\adb reboot edl
Method 2: Using Fastboot
- Download ADB and Fastboot Tool and extract it in your PC (C:/ Drive)
- Boot your device into bootloader
- Open the command window on your PC on the same folder extracted (ADB and Fastboot Tool)
- now enter the command
.\fastboot oem edl
Method 3: By Hardware Test Points / Restore Your device
- Download the QDLoader driver
- Find the EDL PinOUT/Test Point on your device (refer image above to find the test point)
- To enter EDL mode, you need to use a metal tweezer or a conductive metal wire to short the points.
- Once you are done, connect your device to PC using USB cable
- This way, your device will enter EDL mode. Now you can open the QFil or QPST Tool to flash the firmware and restore your device.
How to Bypass FRP lock on Redmi Note 9 Pro using ISP Pinout
Follow this method to bypass the FRP or Google verification on Redmi Note 9 Pro (joyeuse) using ISP pinout method
Required Downloads
Pre-Requirements:
- This guide is for Redmi Note 9 Pro variant only.
- You will need a Windows PC/Laptop and a USB cable.
Instructions
Well, ‘FRP’ is known for the term “Factory Reset Protection.” It’s a security measure taken by Google for Android platforms and devices running on the Android 5.1 Lollipop or above version. This functionality gets activated once you sign in to a Google Account on your Android device. And once it is activated, it will prevent you from using the phone until you enter the previous Google Account Credentials. It will remain the same as well, even after doing the factory data reset.
- Open the back panel of the device at first.
- Connect the wire with the correct ISP Pinout.
- Then connect the ISP Pinout to the UFi Box and connect your device via USB cable to the PC.
- Go to the Device Manager on your PC.
- You will see your device in the list > run the UFi Box and locate the scatter file.
- Go to the user Partition / Special Task and click on Reset FRP on the UFI Box.
- You’re done.
Steps to Hard Reset Redmi Note 9 Pro (Bypass Pattern Lock)
- Remove the back panel of the Redmi Note 9 Pro and connect the wire to the ISP Pinout.
- Next, connect the correct ISP Pinout to the UFi Box.
- Connect your Redmi Note 9 Pro to the PC via a USB cable.
- Head over to the PC and open Device Manager.
- If your device is located there, run the UFi Box.
- Locate the scatter file > go to the Partition / Special Task on the UFI Box.
- Click on Factory Reset.
- Enjoy!
That’s it, guys. We hope this guide was helpful to you in order to bypass the FRP Lock or perform a factory reset on your Redmi Note 9 Pro (joyeuse) handset. If you’ve any queries, let us know in the comments below.
Xiaomi Redmi Note 9 Pro Specifications: Overview
The Xiaomi Redmi Note 9 Pro sports a 6.67 inch IPS LCD display with a Full HD+ resolution. It has a screen to body ratio of 84.5 percent, it can blow up to 450 nits, an aspect ratio of 20:9, a pixel density of 395 Pixel Per Inch ( PPI ). It is protected by Corning Gorilla Glass 5 to the front and rear of the device. Further, it also has splash resistance and a plastic frame.
Underneath the new Note 9 Pro, it sports the latest Qualcomm Snapdragon 720G with 4GB and 6GB of RAM variants. It is also available in 64GB and 128GB of UFS 2.1 internal storage. Talking about optics, the Redmi Note 9 Pro has a quad rear camera set up with a primary 48MP sensor, 8MP secondary ultra-wide-angle sensor, 5MP tertiary macro sensor, and finally another 2MP depth sensor. To the front, it has a 16MP unit with an f/2.0 aperture value. This front camera sits inside the punch hole which the brand calls as the DotDisplay.
This new device from Xiaomi comes with a 5020 mAh battery and this charges over the USB type c port. This massive battery also supports 18W fast charging tech i.e. the QC 3.0 tech. The device is running on MiUi 11 which is based on the latest Android 10. It has a physical fingerprint scanner to the side and also has support for face unlock. Redmi still retains the headphone jack in this device and comes with a single speaker setup. Connectivity options include Wi-Fi 802.11 a/b/g/n/ac, dual-band, Wi-Fi Direct, hotspot. Bluetooth 5.0, A2DP, LE. GPS with A-GPS, GLONASS, GALILEO, BDS, NavIC, infrared port, FM radio. USB 2.0, Type-C 1.0 reversible connector. Other sensors include accelerometer, gyro, proximity, and compass.
