Fix 1: Reset your Beats Solo 3
Resetting your Beats can often resolve minor software glitches or connectivity issues that may be preventing them from charging properly. This simple step can be an effective first troubleshooting method to try.
- Power off the headphones by pressing and holding the power button until they shut down.
- Wait for a few seconds.
- Turn the headphones back on by pressing the power button again.
- Check to see if the headphones are now charging properly.
Fix 2: Hard Reboot your Beats Solo 3
If your headphones still aren’t charging properly, you might try to fix the problem by doing a hard reboot. A hard reboot will fix any issues with the internal components glitching or software bugs. Here’s how to hard reboot your Beats Solo 3:
- Plug the included charging wire into a wall outlet to power your Beats Solo 3 headphones.
- Press and hold the Volume Down and Power buttons simultaneously.
- When the LEDs on your Beats Solo 3 headphones start flashing, let go of the buttons.
- Check if the headphones are now charging correctly.
Fix 3: Charge For At Least An Hour
One simple solution to the problem of your Beats headphones not charging is to charge them for at least an hour. If the battery is fully dead, the charging process could take significantly longer than usual.
After giving your Beats Solo 3 a full charge, you should test if they are working by turning them on.
Keep in mind that if you charge the battery for at least an hour, it will gain enough power to fix the charging problem. If the issue persists, move on to the next solution.
Fix 4: Check The Charging Lights
If your Beats headphones still aren’t charging properly, you can get some insight from their indicator lights. The charging indicator lights might help you figure out what’s wrong. In order to understand the charging lights, you should know the following:
- Solid Red Light: When the red battery indicator light is constantly on, the battery is almost dead. When this indicator glows, it’s time to plug in your headphones for a recharge.
- Flashing Red Light: If the battery indicator light is flashing red, it means the battery is almost out of juice.
- Flashing Light and Low Battery: A reset may be required if you see a flashing red light and your battery life is getting dangerously low. Try doing a factory reset.
- No Light: If the charging indicator lights are off, it could signal that the battery isn’t being charged, but it could also mean that the headphones are off.
Fix 5: Check Your Power Source
If your Beats Solo 3 headphones still aren’t charging properly, check the source you’re feeding them power from. You can’t charge your headphones properly without a reliable power source that can supply the required electrical current. Here’s how to make sure everything is running smoothly and fix any power problems if they exist:
- Make sure that the output of your power source (wall adapter, USB port, or power bank) is compatible with the output of your Beats Solo 3 headphones. Determine the voltage and current from the power source’s labeling or specifications.
- The charger that came with your Beats Solo 3 headphones, or an approved replacement, must be used. If you try to charge your device using a charger that isn’t compatible, your Beats Solo 3 will charge slowly or not at all.
- If you think your power outlet or USB port might be at fault, try using another one to see if the charging problem still occurs. A faulty power source or USB port might occasionally obstruct the charging procedure.
- Invest in a dedicated charging adaptor for your Beats Solo 3 headphones if you want to be sure they get fully charged every time. These converters often deliver the necessary output and help fix incompatibilities between power sources.
Fix 6: Check your Room Temperature
It may seem obvious, but the ambient temperature might affect how well your Beats Solo 3 headphones charge. You can’t charge your wireless Beats headphones if the room temperature is above 40 degrees Celsius (about 104 degrees Fahrenheit) or below 5 degrees Celsius (approximately 41 degrees Fahrenheit), as these temperatures trigger a built-in safety feature.
Even if it’s unlikely that the ambient temperature is the only source of charging issues, it’s still important to take into account. Leaving your headphones in the sun or a hot room will activate the security feature, preventing charging. Let your Beats Solo 3 reach an optimal temperature before you charge it again.
Fix 7: Check The Charging Cable
A faulty charging cable could be the culprit if your Beats headphones won’t charge. It’s a common problem, yet it’s easy to resolve. It’s possible that the charging cable has become damaged or worn out after several uses or after being coiled roughly.
If you suspect that the cable you’re using to charge your headphones is at fault, you can test a new cable. If the second cable is successful in charging your headphones, then you know the first cable is defective.
Use only a genuine Beats cable to charge your headphones, since this cable was developed in close collaboration with Beats to ensure optimal performance. But if you’re seeking a cheaper alternative, a third-party cable that fits the requirements may work.
Always make sure that the cable isn’t bent at extreme angles or pulled with too much force. Its shelf life can be extended through careful cable management.
Cleaning the charging connections may fix your Beats Solo 3’s charging issues. Debris and dirt can collect on the charging contacts over time, disrupting the connection and preventing the headphones from charging properly. If the charging contacts are dirty, cleaning them may help restore normal operation. Follow these simple steps to clean the charging contacts:
- Put your Beats Solo 3 headphones to sleep by turning off the power and unplugging them.
- Look for dust or debris in the charging port and along the cable. If you find any, you can wipe it away with a dry, lint-free cloth or a soft brush.
- Use rubbing alcohol (or isopropyl alcohol) to dampen a clean cloth or cotton swab. A damp cloth or swab is preferable to a leaking one.
- Use the damp cloth or swab to gently clean the charging contacts on the headphones and the charging cable.
- Make sure not to squeeze the headphones too hard or allow any liquid to get inside.
- Check to see if the Beats Solo 3 is now charging.
Fix 9: Update Your Firmware
If your Beats headphones are still having charging issues, try updating the firmware. Firmware updates are important to keep your headphones in good working condition. To maintain peak performance, it is wise to check for firmware upgrades on a regular basis.
Earlier, updating the firmware on your Beats headphones was done through the Beats updater app, which was available on Mac and Windows only. The app is still available for download, although new versions of the app will no longer be available. Rather, Apple is encouraging users to go for over-the-air updates instead. We will cover both options; you can choose the one you find convenient.
Update Firmware Using Beats Updater App
- First, download the Beats updater. Go to the Beats website and click the “Download” button. Both Mac and Windows users can download the updater.
- Use a USB connection to connect your wireless Beats headphones to your laptop or desktop computer. Make sure that the headphones are plugged in correctly.
- Launch the Beats updater application.
- Once you plug in your headphones, it must recognize them.
- The updater will present a list of Beats headphone models; choose Beats Solo 3.
- The update process will now begin. To continue, follow the on-screen prompts.
- Click on the “Update” button. Keep your headphones plugged into your computer at all times when updating.
- Disconnect your headphones from the computer after the firmware update is complete to see if the charging problems have been fixed.
Use OTA Update
- If you have an iPhone, iPad, or Mac, you can update the firmware of your Beats Solo 3 from the Bluetooth settings. Go to Settings > Bluetooth > click on the “i” next to your Beats Solo 3 > About > Firmware version.
- If you have an Android device, download the Beats app for Android from the Google Play Store. Set up your Beats Solo 3 with the app, and you should be prompted to install an update if available.
Fix 10: Replace The Battery
If you have been experiencing charging issues with your Beats Solo 3 headphones and none of the previous solutions have worked, it may be time to replace the battery. Beats Studio and other Beats models use Lithium-ion batteries, which have the advantage of being able to hold a substantial quantity of charge. Nonetheless, these batteries can lose their ability to contain a charge over time.
If you think your battery is faulty, it’s time to visit the service center and get it replaced. This may or may not cost much, depending on the warranty and the warranty policy.
Finally, if none of the solutions work, you should contact Apple Support. Since Apple has acquired Beats, you should get your Beats Solo 3 serviced at any Apple store. You can also contact their customer support for further assistance with the problem.
Final Words
Beats Solo 3 are great headphones but often face difficulties like charging issues. We hope that this guide has helped fix the charging issues on your Beats Solo 3. Remember to keep your Beats Solo 3 connected to the charger for at least an hour before using it. If you still have charging issues, visit an Apple service center or contact the support team for assistance. In the comments section below, let us know which solution helped you fix the issue. Thanks for reading!
